diff --git a/drivers/uart/src/uart_pl011.c b/drivers/uart/src/uart_pl011.c
new file mode 100644
index 0000000..d65269a
--- /dev/null
+++ b/drivers/uart/src/uart_pl011.c
@@ -0,0 +1,220 @@
+/*
+ * Copyright (c) 2019-2021 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+/* Basic PL011 UART driver */
+
+#include "uart_config.h"
+#include "uart_stdout.h"
+#include <stdint.h>
+#include <stdio.h>
+
+#define CNTLQ     0x11
+#define CNTLS     0x13
+#define DEL       0x7F
+#define BACKSPACE 0x08
+#define CR        0x0D
+#define LF        0x0A
+#define ESC       0x1B
+
+/*****************************************************************************/
+/*  UART Control Register Locations                                          */
+/*****************************************************************************/
+#define UART0_DR   *((volatile uint32_t *)UART0_BASE)
+#define UART0_RSR  *((volatile uint32_t *)(UART0_BASE + 0x04))
+#define UART0_ECR  *((volatile uint32_t *)(UART0_BASE + 0x04))
+#define UART0_LCRH *((volatile uint32_t *)(UART0_BASE + 0x2C))
+#define UART0_LCRM *((volatile uint32_t *)(UART0_BASE + 0x28))
+#define UART0_LCRL *((volatile uint32_t *)(UART0_BASE + 0x24))
+#define UART0_CR   *((volatile uint32_t *)(UART0_BASE + 0x30))
+#define UART0_FR   *((volatile uint32_t *)(UART0_BASE + 0x18))
+#define UART0_IIR  *((volatile uint32_t *)(UART0_BASE + 0x1C))
+#define UART0_ICR  *((volatile uint32_t *)(UART0_BASE + 0x44))
+
+/*****************************************************************************/
+/* Received Status Register - RSR                                            */
+/*****************************************************************************/
+#define RSR_OVERRUN_ERROR 0x08
+#define RSR_BREAK_ERROR   0x04
+#define RSR_PARITY_ERROR  0x02
+#define RSR_FRAMING_ERROR 0x01
+
+/*****************************************************************************/
+/* Line Control High Byte Register - LCRH                                    */
+/*****************************************************************************/
+#define LCRH_WORD_LENGTH_8 0x60
+#define LCRH_WORD_LENGTH_7 0x40
+#define LCRH_WORD_LENGTH_6 0x20
+#define LCRH_WORD_LENGTH_5 0x00
+#define LCRH_FIFO_ENABLED  0x10
+#define LCRH_2_STOP_BITS   0x08
+#define LCRH_EVEN_PARITY   0x04
+#define LCRH_PARITY_ENABLE 0x02
+#define LCRH_SEND_BREAK    0x01
+
+/*****************************************************************************/
+/* Line Control Medium Byte Register - LCRM                                  */
+/* This register specifies the high byte of the Baud rate divisor            */
+/*****************************************************************************/
+#define LCRM_BAUD_460800 0x00
+#define LCRM_BAUD_230400 0x00
+#define LCRM_BAUD_115200 0x00
+#define LCRM_BAUD_76800  0x00
+#define LCRM_BAUD_57600  0x00
+#define LCRM_BAUD_38400  0x00
+#define LCRM_BAUD_19200  0x00
+#define LCRM_BAUD_14400  0x00
+#define LCRM_BAUD_9600   0x00
+#define LCRM_BAUD_2400   0x01
+#define LCRM_BAUD_1200   0x02
+
+/*****************************************************************************/
+/* Line Control Low Byte Register - LCRL                                     */
+/* This register specifies the low byte of the Baud rate divisor             */
+/*****************************************************************************/
+#define LCRL_BAUD_460800 0x01
+#define LCRL_BAUD_230400 0x03
+#define LCRL_BAUD_115200 0x07
+#define LCRL_BAUD_76800  0x0B
+#define LCRL_BAUD_57600  0x0F
+#define LCRL_BAUD_38400  0xC
+#define LCRL_BAUD_19200  0x2F
+#define LCRL_BAUD_14400  0x3F
+#define LCRL_BAUD_9600   0x5F
+#define LCRL_BAUD_2400   0x7F
+#define LCRL_BAUD_1200   0xFF
+
+/*****************************************************************************/
+/* Control Register - CR                                                     */
+/*****************************************************************************/
+#define CR_LOOP_BACK_EN   0x80
+#define CR_TIMEOUT_INT_EN 0x40
+#define CR_TX_INT_ENABLE  0x100
+#define CR_RX_INT_ENABLE  0x200
+#define CR_MODSTAT_INT_EN 0x08
+#define CR_UART_ENABLE    0x01
+
+/*****************************************************************************/
+/* Flag Register - FR                                                        */
+/*****************************************************************************/
+#define FR_TX_FIFO_EMPTY  0x80
+#define FR_RX_FIFO_FULL   0x40
+#define FR_TX_FIFO_FULL   0x20
+#define FR_RX_FIFO_EMPTY  0x10
+#define FR_BUSY           0x08
+#define FR_CARRIER_DETECT 0x04
+#define FR_SET_READY      0x02
+#define FR_CLEAR_TO_SEND  0x01
+
+/*****************************************************************************/
+/* Interrupt Identification Register - IIR                                   */
+/*****************************************************************************/
+#define IIR_RX_TIME_OUT 0x08
+#define IIR_TX          0x04
+#define IIR_RX          0x02
+#define IIR_MODEM       0x01
+
+void UartStdOutInit(void) {
+    // Disable the serial port while setting the baud rate and word length
+    UART0_CR = 0;
+
+    // Clear the receive status register
+    UART0_ECR = 0;
+
+    // Set the correct baud rate and word length
+    UART0_LCRL = LCRL_BAUD_115200;
+    UART0_LCRM = LCRM_BAUD_115200;
+    UART0_LCRH = LCRH_WORD_LENGTH_8;
+
+    // Explicitly disable FIFO's for char mode
+    UART0_LCRH &= ~LCRH_FIFO_ENABLED;
+
+    // Enable UART0 (and RX/TX) without interrupts
+    UART0_CR = CR_UART_ENABLE | CR_TX_INT_ENABLE | CR_RX_INT_ENABLE;
+}
+
+unsigned char UartPutc(unsigned char ch) {
+    if (ch == '\n') {
+        (void)UartPutc('\r');
+    }
+    while (UART0_FR & FR_TX_FIFO_FULL)
+        ;
+    UART0_DR = ch;
+
+    return ch;
+}
+
+unsigned char UartGetc(void) {
+    unsigned char c;
+    while (UART0_FR & FR_RX_FIFO_EMPTY)
+        ;
+    c = UART0_DR;
+    if (c == '\r') {
+        c = '\n';
+    }
+
+    return c;
+}
+
+// Get line from terminal
+unsigned int GetLine(char *lp, unsigned int len) {
+    unsigned int cnt = 0;
+    char c;
+
+    do {
+        c = UartGetc();
+        switch (c) {
+        case CNTLQ: /* ignore Control S/Q             */
+        case CNTLS:
+            break;
+        case BACKSPACE:
+        case DEL:
+            if (cnt == 0) {
+                break;
+            }
+            cnt--;          /* decrement count                */
+            lp--;           /* and line pointer               */
+            UartPutc(0x08); /* echo backspace                 */
+            UartPutc(' ');
+            UartPutc(0x08);
+            fflush(stdout);
+            break;
+        case ESC:
+        case 0:
+            *lp = 0; /* ESC - stop editing line        */
+            return 0;
+        case CR: /* CR - done, stop editing line   */
+            *lp = c;
+            lp++;  /* increment line pointer         */
+            cnt++; /* and count                      */
+            c = LF;
+            UartPutc(*lp = c); /* echo and store character       */
+            fflush(stdout);
+            lp++;  /* increment line pointer         */
+            cnt++; /* and count                      */
+            break;
+        default:
+            UartPutc(*lp = c); /* echo and store character       */
+            fflush(stdout);
+            lp++;  /* increment line pointer         */
+            cnt++; /* and count                      */
+            break;
+        }
+    } while (cnt < len - 2 && c != LF); /* check limit and CR             */
+    *lp = 0;                            /* mark end of string             */
+    return 1;
+}