The sample application for Arm® Ethos™-U55 can be deployed on two target platforms, both of which implement the Arm® Corstone™-300 design (see https://www.arm.com/products/iot/soc/corstone-300):
A physical Arm MPS3 FPGA prototyping board
An MPS3 FVP
The FVP is available publicly from Arm Ecosystem FVP downloads . Download the correct archive from the list under
Arm Corstone-300. We need the one which:
For Ethos-U55 sample application, please download the MPS3 version of the Arm® Corstone™-300 model that contains Ethos-U55 and Arm® Cortex®-M55. The model is currently only supported on Linux based machines. To install the FVP:
Unpack the archive
Run the install script in the extracted package
Follow the instructions to install the FVP to your desired location
This section assumes that the FVP has been installed (see Setting up the MPS3 Arm Corstone-300 FVP) to the user's home directory
The installation, typically, will have the executable under
~/FVP_Corstone_SSE-300_Ethos-U55/model/<OS>_<compiler-version>/ directory. For the example below, we assume it to be
To run a use case on the FVP, from the Build directory:
~/FVP_Corstone_SSE-300_Ethos-U55/models/Linux64_GCC-6.4/FVP_Corstone_SSE-300_Ethos-U55 -a ./bin/ethos-u-<use_case>.axf telnetterminal0: Listening for serial connection on port 5000 telnetterminal1: Listening for serial connection on port 5001 telnetterminal2: Listening for serial connection on port 5002 telnetterminal5: Listening for serial connection on port 5003 Ethos-U rev 0 --- Oct 13 2020 11:27:45 (C) COPYRIGHT 2019-2020 Arm Limited ALL RIGHTS RESERVED
This will also launch a telnet window with the sample application's standard output and error log entries containing information about the pre-built application version, TensorFlow Lite Micro library version used, data type as well as the input and output tensor sizes of the model compiled into the executable binary.
Note: For details on the specific use-case follow the instructions in the corresponding documentation.
After the application has started it outputs a menu and waits for the user input from telnet terminal.
For example, the image classification use case can be started by:
~/FVP_Corstone_SSE-300_Ethos-U55/models/Linux64_GCC-6.4/FVP_Corstone_SSE-300_Ethos-U55 -a ./bin/ethos-u-img_class.axf
The FVP supports many command line parameters:
passed by using
-C <param>=<value>. The most important ones are:
ethosu.num_macs: Sets the Ethos-U55 configuration for the model. Valid parameters are
256, and the default one
128. The number signifies the 8x8 MACs performed per cycle count available on the hardware.
cpu0.CFGITCMSZ: ITCM size for the Cortex-M CPU. Size of ITCM is pow(2, CFGITCMSZ - 1) KB
cpu0.CFGDTCMSZ: DTCM size for the Cortex-M CPU. Size of DTCM is pow(2, CFGDTCMSZ - 1) KB
mps3_board.telnetterminal0.start_telnet : Starts the telnet session if nothing connected.
mps3_board.uart0.out_file: Sets the output file to hold data written by the UART (use '-' to send all output to stdout, empty by default).
mps3_board.uart0.shutdown_on_eot: Sets to shutdown simulation when a EOT (ASCII 4) char is transmitted.
mps3_board.visualisation.disable-visualisation: Enables or disables visualisation (disabled by default).
To start the model in
128 mode for Ethos-U55:
~/FVP_Corstone_SSE-300_Ethos-U55/models/Linux64_GCC-6.4/FVP_Corstone_SSE-300_Ethos-U55 -a ./bin/ethos-u-img_class.axf -C ethosu.num_macs=128
-l: shows the full list of supported parameters
--stat: prints some run statistics on simulation exit
--timelimit: sets the number of wall clock seconds for the simulator to run, excluding startup and shutdown.
Note: Before proceeding, make sure you have the MPS3 board powered on, and USB A to B connected between your machine and the MPS3. The connector on the MPS3 is marked as "Debug USB".
Once the board has booted, the micro SD card will enumerate as a mass storage device. On most systems this will be automatically mounted, but you might need to mount it manually.
Also, there should be four serial-over-USB ports available for use via this connection. On Linux based machines, these would typically be /dev/ttyUSB<n> to /dev/ttyUSB<n+3>.
The default configuration for all of them is 115200, 8/N/1 (15200 bauds, 8 bits, no parity and 1 stop bit) with no flow control.
Note: For Windows machines, additional FTDI drivers might need to be installed for these serial ports to be available. For more information on getting started with an MPS3 board, please refer to https://developer.arm.com/-/media/Arm%20Developer%20Community/PDF/MPS3GettingStarted.pdf
NOTE: These instructions are valid only if the evaluation is being done using the MPS3 FPGA platform using
To run the application on MPS3 platform, firstly it's necessary to make sure that the platform has been set up using the correct configuration. For details, on platform set up, please see the relevant documentation. For
Arm Corstone-300, this is available here.
For MPS3 board, instead of loading the axf file directly, the executable blobs generated under the sectors/<use_case> subdirectory need to be copied over to the MP3 board's micro SD card. Also, sectors/images.txt file is used by the MPS3 to understand which memory regions the blobs are to be loaded into.
Once the USB A <--> B cable between the MPS3 and the development machine is connected and the MPS3 board powered on, the board should enumerate as a mass storage device over this USB connection. There might be two devices also, depending on the version of the board you are using. The device named
V2MMPS3 is the
If the axf/elf file is within the ITCM load size limit, it can be copied into the FPGA memory directly without having to break it down into separate load region specific blobs. However, with neural network models exceeding this size, it becomes necessary to follow this approach.
For example, the image classification use case will produce:
./bin/sectors/ └── img_class ├── dram.bin └── itcm.bin
For example, if the micro SD card is mounted at /media/user/V2M-MPS3/:
cp -av ./bin/sectors/img_class/* /media/user/V2M-MPS3/SOFTWARE/
./bin/sectors/images.txt file needs to be copied over to the MPS3. The exact location for the destination will depend on the MPS3 board's version and the application note for the bit file in use. For example, for MPS3 board hardware revision C, using an application note directory named "ETHOSU", to replace the images.txt file:
cp ./bin/sectors/images.txt /media/user/V2M-MPS3/MB/HBI0309C/ETHOSU/images.txt
Open the first serial port available from MPS3, for example, "/dev/ttyUSB0". This can be typically done using minicom, screen or Putty application. Make sure the flow control setting is switched off.
minicom --D /dev/ttyUSB0
Welcome to minicom 2.7.1 OPTIONS: I18n Compiled on Aug 13 2017, 15:25:34. Port /dev/ttyUSB0, 16:05:34 Press CTRL-A Z for help on special keys Cmd>
In another terminal, open the second serial port, for example, "/dev/ttyUSB1":
minicom --D /dev/ttyUSB1
On the first serial port, issue a "reboot" command and press the return key
$ Cmd> reboot
Rebooting...Disabling debug USB..Board rebooting... ARM V2M-MPS3 Firmware v1.3.2 Build Date: Apr 20 2018 Powering up system... Switching on main power... Configuring motherboard (rev C, var A)...
This will go on to reboot the board and prime the application to run by flashing the binaries into their respective FPGA memory locations. For example:
Reading images file \MB\HBI0309C\ETHOSU\images.txt Writing File \SOFTWARE\itcm.bin to Address 0x00000000 ............ File \SOFTWARE\itcm.bin written to memory address 0x00000000 Image loaded from \SOFTWARE\itcm.bin Writing File \SOFTWARE\dram.bin to Address 0x08000000 .......................................................................... File \SOFTWARE\dram.bin written to memory address 0x08000000 Image loaded from \SOFTWARE\dram.bin
When the reboot from previous step is completed, issue a reset command on the command prompt.
$ Cmd> reset
This will trigger the application to start, and the output should be visible on the second serial connection.
On the second serial port, output similar to section 2.2 should be visible:
INFO - Setting up system tick IRQ (for NPU) INFO - V2M-MPS3 revision C INFO - Application Note AN540, Revision B INFO - FPGA build 1 INFO - Core clock has been set to: 32000000 Hz INFO - CPU ID: 0x410fd220 INFO - CPU: Cortex-M55 r0p0 ...
Next section of the documentation: Implementing custom ML application.