Ensure that the files you are using match the requirements of the model you are using. Ensure that cmake parameters are set accordingly. More information on these cmake parameters is detailed in their separate sections.
Note: Preprocessing of the files can also affect the inference result, such as the rescaling and padding operations performed for image classification.
Ensure that your model is in a fully quantized .tflite
file format, either uint8
or int8
, and that it has successfully been run through the Vela compiler.
Also, please check that the cmake parameters used match the input requirements of your new model.
Note: The Vela tool is not available within this software project. It is a separate Python tool that is available from: https://pypi.org/project/ethos-u-vela/. The source code is hosted on https://review.mlplatform.org/plugins/gitiles/ml/ethos-u/ethos-u-vela/.
If you see the following error message when an inference is executed:
NPU config mismatch: npu.macs_per_cc=8 optimizer.macs_per_cc=7 NPU config mismatch: npu.shram_size=48 optimizer.shram_size=24 ERROR - Invoke failed. ERROR - Inference failed.
It shows that the configuration of the Vela compiled .tflite
file doesn't match the number of MACs units on the FVP.
The Vela configuration parameter accelerator-config
used for producing the .tflite
file that is used while building the application should match the MACs configuration that the FVP is emulating. For example, if the accelerator-config
from the Vela command was ethos-u55-128
, the FVP should be emulating the 128 MACs configuration of the Ethos™-U55 block(default FVP configuration). If the accelerator-config
used was ethos-u55-256
, the FVP must be executed with additional command line parameter to instruct it to emulate the 256 MACs configuration instead.
The deploying on an FVP emulating MPS3 page provides guidance on how to instruct the FVP to change the number of MACs units.
Note that when the FVP is launched and the application starts executing, various parameters about the system are logged over UART. These include the MACs/cc configuration of the FVP.
INFO - MPS3 core clock has been set to: 32000000Hz INFO - CPU ID: 0x410fd220 INFO - CPU: Cortex-M55 r0p0 INFO - Ethos-U device initialised INFO - Ethos-U version info: INFO - Arch: v1.0.6 INFO - Driver: v0.16.0 INFO - MACs/cc: 128 INFO - Cmd stream: v0 INFO - Target system design: Arm Corstone-300 - AN552 INFO - Arm Corstone-300 - AN552 platform initialised INFO - ARM ML Embedded Evaluation Kit
If you see following errors when cloning the repository:
fatal: unable to access 'https://review.mlplatform.org/ml/ethos-u/ml-embedded-evaluation-kit/': server certificate verification failed. CAfile: /etc/ssl/certs/ca-certificates.crt CRLfile: none
We suggest to update to the latest common CA certificates:
sudo apt-get update sudo apt-get install ca-certificates
fatal: unable to access 'https://review.mlplatform.org/ml/ethos-u/ml-embedded-evaluation-kit/': error:06FFF089:digital envelope routines:CRYPTO_internal:bad key length
We suggest to export the CURL_SSL_BACKEND
variable as secure-transport
:
export CURL_SSL_BACKEND="secure-transport"
During Vela installation, part of the package is compiled and requires libpython3. If the system lacks this dependency the following error will occur:
x86_64-linux-gnu-gcc -pthread -Wno-unused-result -Wsign-compare -DNDEBUG -g -fwrapv -O2 -Wall -g -fstack-protector-strong -Wformat -Werror=format-security -g -fwrapv -O2 -g -fstack-protector-strong -Wformat -Werror=format-security -Wdate-time -D_FORTIFY_SOURCE=2 -fPIC -DNPY_NO_DEPRECATED_API=NPY_1_9_API_VERSION -I/venv/include -I/usr/include/python3.7 -I/venv/lib/python3.7/site-packages/numpy/core/include -c ethosu/mlw_codec/mlw_codecmodule.c -o build/temp.linux-x86_64-3.7/ethosu/mlw_codec/mlw_codecmodule.o ethosu/mlw_codec/mlw_codecmodule.c:20:10: fatal error: Python.h: No such file or directory 20 | #include <Python.h> | ^~~~~~~~~~ compilation terminated. error: command 'x86_64-linux-gnu-gcc' failed with exit status 1 ---------------------------------------- ERROR: Command errored out with exit status 1: /venv/bin/python -u -c 'import sys, setuptools, tokenize; sys.argv[0] = '"'"'/tmp/pip-install-4rmoh7va/ethos-u-vela/setup.py'"'"' ; __file__='"'"'/tmp/pip-install-4rmoh7va/ethos-u-vela/setup.py'"'"';f=getattr(tokenize, '"'"'open'"'"', open) (__file__);code=f.read().replace('"'"'\r\n'"'"', '"'"'\n'"'"');f.close();exec(compile(code, __file__, '"'"'exec'"'"'))' install --record /tmp/pip-record-jidxiokn/install-record.txt --single-version-externally-managed --compile --install-headers /venv/include/site/python3.7/ethos-u-vela Check the logs for full command output.
To solve this issue install libpython3 on the system.
Vela 3.5.0 increases Python requirement to at least version 3.7, if not installed on your system the following error will occur:
python3 -m pip install ethos-u-vela==3.5.0 ERROR: Could not find a version that satisfies the requirement ethos-u-vela==3.5.0 (from versions: 0.1.0, 1.0.0, 1.1.0, 1.2.0, 2.0.0, 2.0.1, 2.1.1, 3.0.0, 3.1.0, 3.2.0) ERROR: No matching distribution found for ethos-u-vela==3.5.0
Ensure that the minimum Python 3.7 requirement is installed and it's the default version. Check your current installed version of Python by running:
python3 --version
Check your current installed version of Python by running:
python3 --version
For example:
Python 3.6.9
Install the Python 3.7 packages necessary on the system:
sudo apt-get install python3.7 python3.7-venv libpython3.7 libpython3.7-dev
Update the python3
alternatives (set as 1 your previous version displayed at step 1):
sudo update-alternatives --install /usr/bin/python3 python3 /usr/bin/python3.6 1 sudo update-alternatives --install /usr/bin/python3 python3 /usr/bin/python3.7 2
At the prompt, update the configuration by selecting Python3.7 as the chosen default alternative:
sudo update-alternatives --config python3
Python3.7 is now set as default you can check it by running:
python3 --version
Python 3.7.0
Note: After updating to from Python3.6 Python3.7 it may happen that the
gnome-terminal
or the relative shortcuts doesn't work anymore. If when opening it from XTerm withgnome-terminal
the following error appear:Traceback (most recent call last): File "/usr/bin/gnome-terminal", line 9, in <module> from gi.repository import GLib, Gio File "/usr/lib/python3/dist-packages/gi/__init__.py", line 42, in <module> from . import _gi ImportError: cannot import name '_gi' from partially initialized module 'gi' (most likely due to a circular import) (/usr/lib/python3/dist-packages/gi/> __init__.py)Modify the
gnome-terminal
script located in/usr/bin/
and changing the environment (first line of the script) from#!/usr/bin/python3
to#!/usr/bin/python3.6
.
Next section of the documentation: Appendix.
If trying to build on Arm Virtual Hardware and you encounter an error similar to the following:
The virtual environment was not created successfully because ensurepip is not available. On Debian/Ubuntu systems, you need to install the python3-venv package using the following command. apt install python3.8-venv You may need to use sudo with that command. After installing the python3-venv package, recreate your virtual environment. Failing command: ['/home/test/ml-embedded-evaluation-kit/resources_downloaded/env/bin/python3', '-Im', 'ensurepip', '--upgrade', '--default-pip'] Traceback (most recent call last): File "./build_default.py", line 184, in <module> run( File "./build_default.py", line 89, in run (download_dir, env_path) = set_up_resources( File "/home/test/ml-embedded-evaluation-kit/set_up_default_resources.py", line 439, in set_up_resources call_command(command) File "/home/test/ml-embedded-evaluation-kit/set_up_default_resources.py", line 276, in call_command proc.check_returncode() File "/usr/lib/python3.8/subprocess.py", line 448, in check_returncode raise CalledProcessError(self.returncode, self.args, self.stdout, subprocess.CalledProcessError: Command 'python3 -m venv env' returned non-zero exit status 1.
You can fix this error by installing Python virtual environment and removing the corrupted resources_downloaded folder.
sudo apt install python3.8-venv rm -r resources_downloaded
You can then try rebuilding again e.g.
python3 ./build_default.py
and the error should be fixed.